features and benefits four independent voice processing ports in a single, half-size isa slot supporting low- to medium- density voice systems downloadable signal and call processing firmware, spring ware, facilitates feature enhancement and provides field-proven performance based on over four million installed ports c language application program interfaces (apis) for ms-dos*, windows* 95, windows nt*, os/2*, unix*, and linux* shorten the development cycle to get applications to market faster application generators available from third-party providers configure multiple dialog/4 boards in a single pc for easy and cost-effective system expansion, and to build scalable systems from four to 64 ports voice coding at dynamically selectable data rates, 24 kb/s to 64 kb/s, selectable on a channel-by-chan- nel basis for optimal tradeoff in disk storage and voice quality enhanced telephone circuitry and automatic gain control (agc) maintains recording quality over a wide dynamic range perfect digit dtmf (touchtone) provides reliable detection during voice playback - lets callers ?ype- ahead?through menus outbound call progress analyzes outgoing call status quickly and accurately supports pbxpert and pbxpert/32, complimentary utilities that simplify switch integration lifetime warranty the intel dialogic dialog/4 is a four-port voice board in a half-size isa form factor that is ideal for the small/medium business (smb) market segment. the dialog/4 has downloadable signal and call process- ing firmware that facilitates feature enhancement and helps developers build systems that scale from four to 64 ports. intel dialogic dialog/4 voice board datasheet retired product ?this datasheet is for informational purposes only; the product detailed in this datasheet is no longer available. consider migrating to the intel dialogic d/4pciuf combined media board at http://www.intel.com/network/csp/products/8497web.htm .
configurations the intel dialogic dialog/4 board shares a common hardware and firmware architecture with other intel voice boards for maximum flexibility and scalability. you can easily add new features and/or expand the size of the system while protecting your original investment in hard- ware and application code. applications can be ported to lower or higher line-density platforms with minimal modifi- cations. the dialog/4 board installs in ibm* pc xt*/at* (isa bus) and compatible computers (pc platforms based on the intel386 , intel486 , or pentium processors). the dialog/4 board provides everything required for building integrated voice solutions scalable from four to 64 ports. software support the intel dialogic dialog/4 board is supported by system software and sdks for ms-dos*, windows nt*, windows* 95, and linux*. these packages contain a set of tools for developing complex multichannel applications. 2 intel dialogic dialog/4 voice board datasheet pc 4 dialog/4 dialog/4 dialog/4 dialog/4 4 4 4 telephone network (analog loop start lines) applications voice mail/voice messaging interactive voice response audiotex inbound and outbound telemarketing operator services dictation auto dialers notification systems
functional description the intel dialogic dialog/4 board uses a unique dual- processor architecture that combines the signal processing capabilities of a digital signal processor (dsp) with the decision-making and data movement functionality of a general-purpose 80c188 control microprocessor. this dual-processor approach offloads many low-level decision- making tasks from the host computer, enabling develop- ment of more powerful applications. this architecture handles real-time events manages data flow to the host pc for faster system response time reduces host pc processing demands processes dtmf and telephony signaling frees the dsp to perform signal processing on the incoming call each of four loop start telephone line interfaces on the dialog/4 board receives analog voice and telephony signaling information from the telephone network (see block diagram). each line interface uses reliable, solid- state hook switches (no mechanical contacts) and fcc part 68 class b ring detection circuitry. this fcc- approved ring detector is less susceptible to spurious rings created by random voltage fluctuations on the net- work. each interface incorporates circuitry that protects against high-voltage spikes and adverse network condi- tions, letting applications go off-hook any time during ring cadence without damaging the board. inbound telephony signaling (ring and loop current detec- tion) are conditioned by the line interface and routed via a control bus to the control processor. the control proces- sor responds to these signals, informs the application of telephony signaling status, and instructs the line interface to transmit outbound signaling (on-hook/off-hook) to the telephone network. the audio voice signal from the network is sent through a bandpass filter, conditioned by the line interface, and then applied to a coder/decoder (codec) circuit. the codec filters, samples, and digitizes the inbound analog audio signal and passes the digitized signal to a motorola* dsp. based on spring ware firmware loaded in dsp ram, the dsp performs the following signal analysis and opera- tions on this incoming data: automatic gain control (agc) to compensate for varia- tions in the level of the incoming audio signal applies an adaptive differential pulse code modulation (adpcm) or pulse code modulation (pcm) algorithm to compress the digitized voice and save disk storage space detects the presence of tones ?dtmf, mf, or an application-defined single- or dual-frequency tone silence detection to determine whether the line is quiet and the caller is not responding for outbound data, the dsp performs the following oper- ations: expands stored, compressed audio data for playback adjusts the volume and rate of speed of playback upon application or user request generates tones ?dtmf, mf, or any application- defined general-purpose tone 3 datasheet intel dialogic dialog/4 voice board code/data dram 80c188 control processor shared ram pc xt/at bus dsp codec line interface to central office or pbx dspram irq data control bus 1 of 4 shown
the dual-processor combination also performs the follow- ing outbound dialing and call progress monitoring: transmits an off-hook signal to the telephone network dials out (makes an outbound call) monitors and reports results ? line busy or congested ? operator intercept ? ring, no answer ? or if the call is answered, whether answered by a person, an answering machine, a facsimile machine, or a modem when recording speech, the dsp can use different digi- tizing rates from 24 kb/s to 64 kb/s as selected by the application for the best speech quality and most efficient storage. the digitizing rate can be selected on a channel- by-channel basis and can be changed each time a record or play function is initiated. outbound processing is the reverse of inbound processing. the dsp processed speech is transmitted by the control microprocessor to the host pc for disk storage. when replaying a stored file, the microprocessor receives the voice information from the host pc and passes it to the dsp which converts the file into digitized voice. the dsp sends digitized voice to the codec to be converted into analog voice and then to the line interface for transmission to the telephone net- work. the on-board microprocessor controls all operations of the dialog/4 board via a local bus and interprets and executes commands from the host pc. this microprocessor handles real-time events manages data flow to the host pc to provide faster system response time reduces pc host-processing demands processes dtmf and telephony signals before passing them to the application frees the dsp to perform signal processing communications between this microprocessor and the host pc is via the shared ram that acts as an input/out- put buffer, increasing the efficiency of disk file transfers. this ram interfaces to the host pc via the xt/at bus. all operations are interrupt-driven to meet the demands of real-time systems. all dialog/4 boards installed in the pc share the same interrupt line. when the system is ini- tialized, spring ware firmware to control all board opera- tions is downloaded from the host pc to the on-board code/data ram and dsp ram. this downloadable firmware gives the board all of its intelligence and enables easy feature enhancement and upgrades. 4 intel dialogic dialog/4 voice board datasheet
5 technical specifications number of ports four max. boards/system 16 analog network interface onboard loop start interface circuits microprocessor 80c188 digital signal processor motorola* dsp56001 host interface bus compatibility ibm pc xt/at (isa) bus speed 4 mhz to 12 mhz, 70 nsec back-to-back bus cycle shared memory 8 kb page, switch selectable on 8 kb boundaries base addresses d000h (default) a000h c000h interrupt level irq 2 to irq 7 jumper selectable one irq is shared by all dialog/4 boards telephone interface ? trunk type loop start (or ground start for answer only) impedance 600 ohms nominal ring detection 25 vrms minimum 15.3 hz to 68 hz, 150 vrms maximum loop current range 20 ma to 120 ma, dc (polarity insensitive) receive signal/noise ratio 70 db, referenced to ?5 dbm crosstalk coupling ?0 db at 1 khz channel to channel frequency response 300 hz to 3400 hz ? db (transmit and receive) connector two rj-11 type power requirements +5 vdc .75 a +12 vdc 40 ma ?2 vdc 40 ma operating temperature 0? to +50? storage temperature ?0? to +70? humidity 8% to 80% noncondensing form factor pc xt (isa) 7 in. long (17.5 cm) 0.652 in. wide (1.63 cm) 4.5 in. high (11.25 cm) (excluding edge connector) safety and emi certifications united states fcc part 68 id#: ebzusa-65588-vm-e ul: e143032 canada doc: 885-4452a ulc: e143032 estimated mtbf 309,000 hours per bellcore method i warranty intel telecom products warranty information at http://www.intel.com/network/csp/products/3144web.htm datasheet intel dialogic dialog/4 voice board
6 spring ware technical specifications audio signal receive range ?0 dbm to ?3 dbm (nominal), for average speech signals ? configurable by parameter** automatic gain control application can enable/disable. above ?8 dbm results in full-scale recording, configurable by parameter.** silence detection ?8 dbm nominal, software adjustable** transmit level (weighted average) ? dbm nominal, configurable by parameter** transmit volume control 40 db adjustment range, with application-definable increments and legal limit cap frequency response 24 kb/s 300 hz to 2600 hz ? db 32 kb/s 300 hz to 3400 hz ? db 48 kb/s 300 hz to 2600 hz ? db 64 kb/s 300 hz to 3400 hz ? db audio digitizing 24 kb/s adpcm @ 6 khz sampling 32 kb/s adpcm @ 8 khz sampling 48 kb/s ?law pcm @ 6 khz sampling 64 kb/s ?law pcm @ 8 khz sampling digitization selection selectable by application on function call-by-call basis playback speed control pitch controlled available for 24 and 32 kb/s data rates adjustment range: ?0% adjustable through application or programmable dtmf control dtmf tone detection dtmf digits 0 to 9, *, #, a, b, c, d per bellcore* lssgr sec 6 dynamic range default set to ?6 dbm to ? dbm per tone, configurable by parameter** minimum tone duration 40 ms, can be increased with software configuration interdigit timing detects like digits with a 40 ms interdigit delay. detects different digits with a 0 ms interdigit delay. twist and frequency variation meets bellcore lssgr sec 6 and eia 464 requirements acceptable twist 10 db signal/noise ratio 10 db (referenced to lowest amplitude tone) noise tolerance meets bellcore lssgr sec 6 and eia 464 requirements for gaussian, impulse, and power line noise tolerance cut-through detects down to ?6 dbm per tone into 600 ohm load impedance talk off detects less than 20 digits while monitoring bellcore tr-tsy-000763 standard speech tapes. (lssgr requirements specify detecting no more than 470 total digits.) detects 0 digits while monitoring mitel speech tape #cm 7291. global tone detection tone type programmable for single or dual max. number of tones application-dependent frequency range programmable within 300 hz to 3500 hz max. frequency deviation programmable in 5 hz increments frequency resolution less than 5 hz. note: certain limitations exist for dual tones closer than 125 hz apart. timing programmable cadence qualifier, in 10 ms increments dynamic range programmable, default set at ?6 dbm to +3 dbm per tone intel dialogic dialog/4 voice board datasheet
7 spring ware technical specifications (cont.) global tone generation tone type generate single or dual tones frequency range programmable within 200 hz to 4000 hz frequency resolution 1 hz duration 10 ms increments amplitude ?3 dbm0 to ? dbm0 per tone nominal, programmable mf signaling mf digits 0 to 9, kp, st, st1, st2, st3 per bellcore lssgr sec 6, tr-nwt-000506 and ccitt q.321 transmit level complies with bellcore lssgr sec 6, tr-nwt-000506 signaling mechanism complies with bellcore lssgr sec 6, tr-nwt-000506 dynamic range for detection ?5 dbm0 to ? dbm0 per tone acceptable twist 6 db acceptable freq. variation less than ? hz call progress analysis busy tone detection default setting designed to detect 74 out of 76 unique busy/congestion tones used in 97 countries as specified by ccitt rec. e., suppl. #2. default uses both frequency and cadence detection. application can select frequency only for faster detection in specific environments. ring back detection default setting designed to detect 83 out of 87 unique ring back tones used in 96 countries as specified by ccitt rec. e., suppl. #2. uses both frequency and cadence detection. positive voice detection accuracy >98% based on tests on a database of real world calls in north america. performance in other markets may vary. positive voice detection speed detects voice in as little as 1/10th of a second positive answering machine detection 85% based on application and environment accuracy fax/modem detection preprogrammed intercept detection detects entire sequence of the north american tri-tone. other sit tones can be programmed. dial tone detection before dialing application enable/disable supports up to three different user-definable dial tones programmable dial tone drop out debouncing tone dialing dtmf digits 0 to 9, *, #, a, b, c, d per bellcore lssgr sec 6, tr-nwt-000506 mf digits 0 to 9, kp, st, st1, st2, st3 frequency variation less than ? hz rate 10 digits/s, configurable by parameter** level ?.0 dbm per tone, nominal, configurable by parameter** pulse dialing 10 digits 0 to 9 pulsing rate 10 pulses/s, nominal, configurable by parameter** break ratio 60% nominal, configurable by parameter** datasheet intel dialogic dialog/4 voice board
8 spring ware firmware technical specifications (cont.) analog display services interface (adsi) fsk generation per bellcore tr-nwt-000030 cas tone generation and dtmf detection per bellcore tr-nwt-001273 ** all specifications are subject to change without notice. hardware system requirements intel386 , intel486 , or pentium processor ibm pc at (isa) bus or compatible computer operating system hardware requirements vary according to the number of channels being used recommended cables the dialog/4 does not come with the y adapter (rj-14 to rj-11) and is sold separately. the item market name for this cable is cblrj14torj11ya. intel dialogic dialog/4 voice board datasheet
to learn more, visit our site on the world wide web at http://www.intel.com . 1515 route ten parsippany, nj 07054 phone: 1-973-993-3000 information in this document is provided in connection with intel products. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. except as provided in intel? terms and conditions of sale for such products, intel assumes no liability whatsoever, and intel disclaims any express or implied warranty, relating to sale and/or use of intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. intel products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuc lear facility applications. intel may make changes to specifications, product descriptions, and plans at any time, without notice. positive answering machine detection/positive voice detection these performance results were measured using specific computer systems and/or components within specific lab environments and under specific system configurations. any difference in system hardware, software design, or configuration may affect actual performance. the results are furnished for informational use only and should not be construed as a commitment by intel. intel a ssumes no responsibility or liability for any errors or inaccuracies. outbound dialing/telemarketing outbound dialing systems may be subject to certain laws or regulations. intel makes no representation that intel products will satisfy the requirements of any such laws or regulations (including, without limitation, any regulations dealing with telemarketing). intel, intel dialogic, pentium, and the intel logo are trademarks or registered trademarks of intel corporation or its subsidia ries in the united states and other countries. intel, intel386, intel486, intel dialogic, pentium, and the intel logo are trademarks or registered trademarks of intel corpora tion or its subsidiaries in the united states and other countries. * other names and brands may be claimed as the property of others. ? average speech mandates +16 db peaks above average and preserves 13 db valleys below average. analog levels: 0 dbm0 corresponds to a level of +3 dbm at tip-ring analog point. values vary depending on country requirements; contact your intel sales engineer. printed in the usa copyright ?2002-5 intel corporation all rights reserved. e printed on recycled paper. 09/05 00-2419-008
|
